Runquan Water Saving Equipment Co

Toilet water saver includes a toilet in a groove, which is specially used in grooved toilets (the toilet tank has an automatic water tank, and the urinal tank does not need a water tank). It is a product that achieves the purpose of water saving through human body induction. The most common one is The working principle of the siphon water tank is: tap water is continuously injected into the water tank, and the water surface continues to rise. When the water surface submerges the siphon tube, a siphon phenomenon occurs, and the water tank begins to discharge water. When the water surface drops below the water inlet of the siphon tube, the water discharge stops. Completed a cycle. The toilet water-saving device can be used by someone, and the machine will work according to the instructions. It will automatically flush when the water tank is filled with water. If no one is using it, the machine will not move, effectively achieving intelligent water conservation. > The toilet water saver can save more than > the water bill and avoid the losses caused by a large amount of flushing of the water tank in the bathroom. Since the toilet water saver is a non-contact water-saving device, it not only effectively prevents bacterial cross-infection, but also water-saving effect is as high as above. It is currently widely used in public toilets with toilet troughs. Especially due to the current drought in southwest my country and the overflow of water resources, places with concentrated crowds such as schools, railway stations, and bus stations should integrate resources and strengthen environmental awareness of water conservation.
>Working principle of toilet water-saving device
> Toilet water-saving device is composed of infrared thermal detector, microcomputer programmable controller and low-voltage DC solenoid valve. Its working principle is to complete its work through infrared human body induction. , when someone moves in front of the detector, the red light of the detector immediately flashes, indicating that the person has been sensed. At the same time, the detector transmits the sensing signal to the microcomputer programmable controller, and the controller controls the solenoid valve to open the water, and the water filling time can be adjusted freely. When someone comes, the water is released, and no one stops the water. It is especially suitable for trench toilets in schools, institutions, shopping malls, factories and other units. It has high water saving efficiency, safety and energy saving. Human body infrared sensing > recognition, can identify objects (clothing) of different colors and materials, with zero leakage rate.
>Installation method
> >Use screws to fix the microcomputer program controller and infrared detector on the wall. The detector can be installed along the wall or on the ceiling. The infrared probe sensing window needs to be aligned with the toilet sink or Urinal steps.
> > Install the solenoid valve on the water inlet pipe. Pay attention to the direction of the water inlet. If there is a filter, connect it to the water inlet pipe, as indicated by the arrow.
> > Connect the solenoid valve and infrared detector to the terminals on the microcomputer controller.
> >, then connect the C power supply to the terminal block on the microcomputer controller.
>Functional features of toilet water saver
> >, Automatic induction: fully automatic intelligent control by microcomputer, without direct human contact, which can effectively avoid bacterial cross-infection.
> >Digital adjustment: It only takes a few seconds to adjust program parameters.
> > High reliability: microcomputer control technology, no batteries required, the program will never be lost under any circumstances, the system is designed according to industrial standards
> > Suitable for various harsh environments: whether it is high temperature in summer, Even in severe cold temperatures of more than ten degrees below zero, the product can still work normally.
> Safe to use: Install at a height of 1.3 meters or above to avoid personal contact and avoid human damage.
> >Easy installation: no embedded parts in the wall, installation only takes hours.
> > High return on investment: water saving rate, the entire investment can be recovered within ~ months.
>Toilet water-saving device water-saving effect table
> The water tank is flushed once every minute. The price of water depends on the situation in each region. The following data is for reference only!
> >

<> >Automatic water tank>

(Stool tank)
<> >Water pipes are constantly flowing>

(Urine tank)
<> >Toilet water saver>

(Urine tank)
<> Number of flushes per day
<> times
<> hours
<> times
<> water volume per flush
<> liters
<> .liter>/minute
<> liters
<> Daily water consumption
<> .tons
<> .tons
<> .tons
<> Monthly water consumption
<> tons
<> tons
<> tons
<> Save water bills
<> yuan
<> yuan
<>. . . . . .
<> Service life
<> Months
<> Long term
<> More than years
<> Effect of use
<> Frequent use, easy to break out Fault
<> Waste of water and poor flushing effect.
<> Hygiene, energy saving, and avoid bacterial cross-infection.
>Daily maintenance of toilet water-saving devices
> Toilet water-saving devices control the water control system through solenoid valves. Due to long-term use, there will be impurities in the pipes. Generally, a Clean the water inlet filter once a month. If the water volume becomes smaller, disassemble the inside of the solenoid valve, clean it first, and then reinstall it as it is, which can extend the service life of the machine.
>Common Troubleshooting of Toilet Water Saver
> > If there is a sensor (indicator light is on) but no water comes out: Check whether the solenoid valve filter system is blocked by impurities, clean it, and disassemble the solenoid valve to clean the internal components. , and then reinstall it as it is. If the solenoid valve does not work, just put a new solenoid valve coil directly.
> >. No sensor (indicator light does not light up), water often flows or no water comes out: Check whether the circuit is connected properly and whether there is power supply. If everything is normal, replace the infrared detector.
> If there is normal water flow (indicator light is on), clean the filter and solenoid valve and replace them as they are.
>Toilet water-saving device installation diagram (see lower right)
>< /C:/C~/~/C~/>< /C:/C~/~/C~/>< br/>The trench-type public toilet water-saving device is to install a solenoid valve on the water inlet pipe of the original automatic water tank, and install an infrared sensor on the ceiling at the entrance of the toilet trough or urinal trough. The infrared sensor automatically detects the scene and detects when someone is there. After entering the public toilet, the infrared sensor sends the detected signal to the control box. The microcomputer in the control box issues instructions after performing the predetermined program and controls the solenoid valve to inject water into the automatic water tank for flushing. If no one enters the public toilet, the entire system Will > stand still and never flush. In this way, the hygienic and water-saving use effects of unattended and automatic management, flushing when there are people and stopping when no one is available, are achieved.